Keeping Skunks and Raccoons Out From Under Your Deck: Why Winter Is the Window
If something has been digging along the edge of your deck this fall, or you've caught a whiff of skunk under the house at night, now is the time to deal with it. Not in April.
The reason is the calendar. UC's pest management program says striped skunks breed in February and March, and raccoon young are generally born in April or May. Both animals like the same place to raise them: a dry, dark space under a deck, porch, shed, or house. Once there's a litter under there, you can't just seal the opening. You wait until the young are big enough to leave with their mother, and that can take you well into summer.
So the window is now, November through January. Here's what to use, how to put it in so they can't dig under it, and how to make sure nobody's home before you close it up.
What UC Actually Recommends
UC's raccoon guide gives the spec in one sentence. Open spaces under porches, decks, and sheds should be tightly screened with 10-gauge 1/4- or 1/3-inch galvanized hardware mesh, with the bottom edge buried at least 6 inches deep, bent outward for 12 inches, and covered back over with soil. UC says that one barrier keeps out skunks, opossums, squirrels, and rats along with the raccoons.
Three things in there are worth slowing down on.
The opening: 1/4 or 1/3 inch. An adult skunk or raccoon can't fit through anything close to that. The small opening is for the rest of the list. Rats need about 1/2 inch and mice about 1/4 inch, which we went through in rodent-proofing your house for winter. Santa Clara County's vector control district also recommends 1/4 inch hardware cloth for sealing off porches and decks. In mesh count terms, 1/4 inch is 4 mesh and 1/3 inch is 3 mesh. If that naming is new to you, here's why 1/4 inch hardware cloth is called 4 mesh.
The wire: 10 gauge. That's about 0.135 inch wire, roughly five times thicker than the 23 gauge on a typical roll of 1/4 inch hardware cloth from the hardware store. UC calls raccoons "powerful animals," and they have hands. A skunk digs. A raccoon pulls. Light mesh that's held on with a few staples is something a raccoon can peel back at a corner.
The footer: 6 inches down, 12 inches out. This is the part people skip, and it's the part that matters most for skunks. A skunk that hits a wall of mesh starts digging at the base of it. If the mesh goes straight down 6 inches, the skunk digs 7. If the mesh turns outward along the ground, the skunk is digging on top of it and never finds the bottom edge.
Picking the Mesh
Ten gauge, 1/4 inch, galvanized is a heavy, specialty material, and you won't find it at most hardware stores. Here's how the options compare, all in mesh we stock.
| Mesh | Wire | Clear opening | Where it fits |
|---|---|---|---|
| 1/4" opening 304 stainless, .120" wire | 0.120" (about 11 ga) | 0.250" | Closest to UC's spec. For raccoons that are already pulling at the skirting. |
| 4 mesh 304 stainless, .105" wire | 0.105" (about 12 ga) | 0.145" | Heavy wire with a small hole. Stops mice too. |
| 4 mesh 304 stainless, .063" wire | 0.063" (about 16 ga) | 0.187" | A good all-round choice for skunks, and it lasts in the ground. |
| 4 mesh 304 stainless, .047" wire | 0.047" (about 18 ga) | 0.203" | Comes 60" wide, enough for a tall skirt plus the footer in one piece. |
| 3 mesh 21 ga galvanized hardware cloth | 0.032" | About 0.30" | UC's 1/3 inch opening at a hardware cloth price. Fine for skunks. Light for a determined raccoon. |
| 2 mesh 19 ga galvanized hardware cloth | 0.041" | About 0.46" | Keeps out skunks and raccoons, but not mice or young rats. |
Why stainless for the footer. Half of this barrier is buried in damp soil, and that's where galvanized wire goes first. The zinc coating gets used up, the wire rusts, and in a few winters there's a gap in the one place you can't see. We cover the coating side of that in galvanized before vs. after weld. 304 stainless doesn't have a coating to lose. If you're close to the Bay or the ocean, 316 is worth asking about.
Plan for the width. The footer alone takes 18 inches of mesh, 6 down and 12 out. Add the height from the ground to the deck framing, plus a few inches to fasten, and a 24 inch roll is usually too narrow. Measure the tallest stretch of skirt before you order. Most decks end up needing 36 to 60 inches.
Make Sure Nobody's Home First
Sealing an animal in is worse than leaving the hole open. A trapped skunk or raccoon will try hard to get out, often through your crawlspace, and if it dies under there you'll know.
- Find every opening first. Walk the whole perimeter of the deck or house and close off everything except the one hole that's clearly in use. Look for packed-down dirt, a worn path, or hair caught on the edge.
- Check whether it's being used. A common trick is to loosely plug the last hole with crumpled newspaper or loose soil, or sprinkle flour in front of it, and look the next morning. Skunks and raccoons are both mostly out at night. If the plug is pushed out or there are tracks leading away, something went out. If it stays untouched for a few nights in a row, the space is probably empty.
- Use a one-way door if it's occupied. UC's skunk guide describes a one-way exit gate that lets an animal out and won't let it back in. Leave it up for several nights before you close the hole for good.
- Don't do this from late spring into summer without checking for young. If there's a litter under there, a one-way door separates the mother from her young. That's the whole reason to do this work in winter.
How to Install It
- Dig a trench. Along the outside of the skirt, dig down 6 inches and out 12 inches. An L-shaped trench is easier than it sounds: a flat spade and a mattock do most of it.
- Fasten the top to solid framing. Screws with fender washers, or a wood batten screwed over the edge, every 6 to 8 inches. Staples alone are what a raccoon peels off first.
- Run the mesh down and bend it out. Bend it at the bottom of the trench so the last 12 inches lies flat, pointing away from the deck. Overlap the seams between pieces by a few inches and tie them with wire.
- Backfill and tamp. Cover the footer with soil. Gravel or pavers on top make it even harder to dig.
- Cover it if you want it to look nice. Lattice is fine as a cover. On its own it isn't a barrier. Put the mesh behind it.
If you built a chicken coop this fall, it's the same buried apron we described in hardware cloth vs. chicken wire for a coop. And for the same reason chicken wire doesn't belong on a coop, it doesn't belong on a deck. The openings are too big and the wire is too light.
Take Away the Reason to Visit
Mesh closes the den. It doesn't change why they came to your yard. The usual attractants are pet food left outside, garbage cans without tight lids, fallen fruit, and lawns with grubs, which is what that fall digging usually is. Bring the cat food in at night and the deck becomes a lot less interesting.
Two Health Notes
Rabies. In California, skunks are the second most common rabid animal after bats. The state confirmed rabies in 179 bats and 19 skunks in 2023. A skunk that's out in the daytime, stumbling, or unusually bold is worth a call to animal control. Don't handle one.
Raccoon latrines. Raccoons use the same spot as a toilet over and over, often on a deck, a roof, or a woodpile. Their droppings can carry raccoon roundworm, which can make people seriously ill, young children especially. Wear gloves and follow the CDC's cleanup advice rather than just hosing it off.
Trapping and Relocating
A lot of people's first idea is to trap the animal and drive it somewhere. In California that isn't an option. Under the state's trapping regulations, Title 14, Section 465.5, trapped furbearing and nongame mammals, a group that includes skunks and raccoons, must be released immediately where they were caught or killed. Traps also have to be registered with the Department of Fish and Wildlife and checked every day. If you want an animal removed, hire a licensed wildlife control operator, or call your county's vector control district. Several Bay Area districts will advise on skunks and raccoons.
Exclusion is the part that keeps it from happening again next winter, and it's the part you can do yourself.
Frequently Asked Questions
What size hardware cloth keeps skunks out?
UC recommends 1/4 or 1/3 inch mesh, buried 6 inches and bent out 12 inches. The small opening also keeps out rats, which use the same spaces. An adult skunk can't get through 1/2 inch mesh either, but it will dig under any barrier without a footer.
Is lattice enough to keep raccoons out from under a deck?
Not by itself. Wood or vinyl lattice has openings of an inch or more and breaks under a raccoon's pull. Use it as a cover over heavy mesh.
How deep do skunks dig?
Deep enough to get under a barrier that only goes straight down. That's why UC's spec turns the bottom of the mesh outward for 12 inches instead of just burying it deeper. A skunk digging at the base hits mesh and gives up.
When is the best time to skunk-proof a deck?
Late fall through January, before skunks breed in February and March and before raccoon young arrive in April and May. In late spring and early summer, there's a real chance of sealing young in.
Will galvanized hardware cloth rust in the ground?
Eventually, yes. How fast depends on the soil and how wet it stays, but the buried footer is where it fails first. Stainless lasts a lot longer underground, which is why we suggest it for the footer even if you use galvanized above ground.
We cut hardware cloth and stainless mesh to the width and length you need, so you're not buying a 100 foot roll for one deck. Send us the length of the perimeter and the height of the skirt, and we'll quote it. If you want to see and feel the difference between 23 gauge and .120" wire before you order, we'll mail you a free sample. Family-owned since 1938, when we started on Howard Street in San Francisco. Now we're in Hayward, and a real person answers the phone at (510) 887-8787.
This article is general information about wire mesh, not wildlife control or legal advice. For an animal that's already under your house, talk to a licensed wildlife control operator or your county vector control district. For trapping rules, the California Department of Fish and Wildlife has the final word.
